Director Series
Using the crossover on a Director Amplifier
The following information applies to the Director D2800, D4600, M4800, M4840, M6400, and M6800 amplifiers, and does not apply to the Dante CM amplifiers. Each zone on the Director amplifier has a crossover control with that can be used to create a ...
Using a Powered Subwoofer with a Director M-series amplifier
To add a powered subwoofer or a secondary subwoofer amp with your AudioControl Director amplifier, you can use the amp's Digital outputs to send signal to the subwoofer. Digital A & B outputs On an M4800, M4840, M6400, and M6800, the Digital A & B ...
Directors falling offline in Crestron & Crestron Home
If Crestron is having difficulty staying connected to the Directors, even when the Directors are powered on and their web interfaces are accessible, you should update your Crestron module to the latest version available on our website ...
Setting up Groups in a Director amplifier with Control4
You may have multiple sets of speakers you want to control in single area in your distributed audio system, the Grouping feature in the Director amps is here to help. Combine this with Control4 for a seamless user experience. Set up your groups in ...
How to use Input Sensitivty on a Director, CM, or RS amplifier
Input Sensitivity controls allow you to make the inputs on your amplifier more or less sensitive to incoming signal from audio sources. To change the input sensitivity, navigate to the amp's web interface, open the Global Settings by clicking the ...
How to use the Trim on a Director or CM amplifier
Trim allows you to make small adjustments to the overall output level of a selected zone. You can find the trim controls on the right side of each zone, above the volume slider. In most circumstances, leaving it at 0 is the best bet, but there are ...
How to use Groups on the Director amplifiers
The AudioControl Director series amplifiers allow you to group 2 or more zones together so they act as one. This is useful if you have multiple sets of speakers for a single area, and you want them to all share the same input, volume level, and power ...
Creating a Stereo Image with Bridged Speakers on Architects and Directors
Bridged outputs are always Mono When bridging channels together, the resulting output is a mono output created by summing the left & right input signals together. However, if there are 2 zones outputting to bridged speakers and you want one to by the ...
There are blinking red LEDS on the front panel of my Director amplifier
If you have a Director amplifier series D4600, D2800 or matrix series M6400 or M6800 and you notice that the bottom LED of each LED ladder is blinking ready, do not be alarmed. THIS IS NORMAL The red LED is a status light, or “heartbeat” LED. Each ...
What is the default IP address of my Director D/M, CM 70 volt, or RS series amplifier?
Default IP Address of AudioControl Amplifiers The default IP address for our Director/Director Matrix distribution amplifiers, CM 70 volt amplifiers, and RS 500/1000 subwoofer amplifiers is 192.168.0.249. If the amplifier does not receive an IP ...
Is there Lip Sync (delay) on the Director amplifiers?
Yes! There is a Delay setting on The Director amplifiers. In our 16 channel amps, the setting is only present on Zones 5 – 8, and on our 8 channel amps it's available on all 4 zones. Control is from 0 – 19, in 5 ms increments for a total of 100 ms of ...
What port do I use to connect to my Director amplifier for IP Control?
You can control our Director networked amplifiers via port 23 in either a telnet session or via your chosen automation system.
How to upload speaker profiles to your Director, CM 70 volt, and RS series amplifiers?
This article refers to uploading speaker profiles for the Director and Director Matrix DSP amplifiers, the CM series 70 volt amplifiers, and for the RS500 or RS1000 subwoofer amplifiers. Where to find Speaker Profiles To upload the speaker profiles, ...
How to assign a static IP address to my Director, CM, or RS series amplifiers?
This article refers to setting a static IP address on the Director and Director Matrix DSP amplifiers, CM series 70 volt amplifiers, and the RS500 or RS1000 subwoofer amplifiers. The example image below is for a Director amp running firmware 2.0.xx ...
How do I access the web interface for my Director, CM 70 volt, and RS series amplifiers?
This article refers to accessing the web interface for the Director and Director Matrix DSP amplifiers, CM 70 volt, and RS500 and RS1000 subwoofer amplifiers. Connect the Director or RS amplifier to an existing DHCP network using the Ethernet port. ...
Firmware updates for Director/Director Matrix DSP amplifiers.
This article refers to firmware updates for the D4600, D2800, M6800, M6400, M4800, & M4840 DSP amplifiers. Download the firmware from the AudioControl website via the product page and log into the web interface by entering the IP address of the ...
How to bridge amplifier channels on Director and Architect multi-zone home amps.
Introduction AudioControl Director and Architect series amplifiers have the capability to bridge amplifier channels together to deliver more power to your speakers. Bridging amplifier channels combines a stereo pair of channels into a single mono ...